![]() You have 10 chances to enter the right 5 digit code. That is when you enter the 1st of the 5 digits, the letter C appears, enter the next digit, the letter O appears, enter the next digit, the letter D appears, enter the last digit, the letter E apperas, the radio is reset, ready to go, if you got the 5 correct numbers entered. The next preset button you push, starts the whole thing over again. once the word is spelled out, by entering ANY 5 numbers, if ANY of the 5 is wrong, the radio displays a message "Error" and then a number 1 thru 10. once the word is spelled out, from entering the correct 5 digits, the radio is reset, ready to go.īUT if you miss a number, enter a wrong number, whatever, each number pressed, still makes a letter appear from the word "code". When you use the "preset keys" (the keys on the radio with numbers on them) to enter the code, each time you press a code number, a letter appears. Its posible that when hooking up the jump it was done incorectly and blew up the radio Of note: new streo >theres a blue wire marked ant that goes to the amplifyer if not there you need to find the orange accsesory wire coming from the turn key igntion>check for power when ignition is in the on & off states could be yellow in some cars but is usaly orange if this wire has on and of state controled by the turn key igntion this would be the wire to tap into for the amplyfire and the radio main powerĬheck your radio's instaltion guide for code errors ![]() Is the turn key igntion system hooked into the amp/stero antena lead so that thy are shut of when the ignition is? Have you resently installed a new stero or amplifyer? ![]() What caused the batery to go dead in the first place?ģ) battery is old and not taking a charge anymoreĤ) new stero installed incorectly and drainging the batery Try disconecting the positive terminal of the batery for sevral minets (5-10) this will reset the brain box memory for the stero aswell as for the car it self. Ĭertified Auto Service Repair for Audi BMW Greensboro Jaguar Land Rover. After 3 more incorrect entries the radio locks up again for 60 min. After 3 more incorrect entries (a total of 9 incorrect entries) the waiting time is increased to 60 min. After 3 more incorrect entries the radio is again disabled for 10 min. NOTE: The waiting time continues to run only when the radio is switched on.Īfter expiration of the waiting time the word "CODE" appears on the display again and the correct code number can be entered. After the code has been entered three times incorrectly the word "WAIT" appears on the display and the radio is disabled for approx. If the wrong code number has been entered and confirmed, the word "CODE" appears on the display again. The radio switches on automatically and displays the station or frequency stored for station button 1. A correction can be made only by reentering the entire code number.Ĭonfirming the code number: Press seek-UP/seek-DOWN or SCAN button. In this state the code number can be written over repeatedly. After all 5 digits are entered, the first digit flashes again. number 1, station button 1.Īfter entering the first digit the word "CODE" disappears and the digit entered is displayed followed by 4 dashes. NOTE: The five-digit code number for this radio is printed on the CODE CARD which you were given.Įnter the code number with station buttons, e.g. After switching on the ignition and the radio the word "CODE" appears on the display and the letter "C" flashes. If the radio is disconnected from the power supply it is not ready for operation when reconnected. Let me know if you have any trouble with it. I've attached the procedure for entering the code below. I assume you've already done that though. ![]() It should be printed on a card that comes with those booklets. Please check the information that came along with the owner's manual.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |